ML&S Distribution

Top Deals

Results : 1 - 18 of 18 |Show
Sort by :
Page of 1
All In One Kit (AIO)

The Front Camera kit (New Revision) is designed for switching between the front and the backup cameras. Multiple options are ...

£159.00(Inc VAT at 20%)
3rd Brake Flasher kit (ST(ND)/RF/PRHT)

Due to component shortages not currently available.  Plug-n-Play kit for easy installation of 3rd Brake Flasher. No tools ...

£49.00(Inc VAT at 20%)
Trunk Organizer for Mazda MX-5

4 partitions made from black 1/4″ MDF and 4 3D printed plastic caps. Available for 2016+ (ND) and for 2006-2015 (NC).

£70.00(Inc VAT at 20%)
Trunk Lid Popper

Stainless Steel torsion springs with mounting hardware. Latest revision. Installation instructionWARNING: this kit will not work with extra weight on the lid, like heavy liner , luggage rack, etc.

£99.00(Inc VAT at 20%)
FOBO Bike 2

OBO 2 T-Valve Accessory. Suitable for rim valve hole of diameter 8.3 mm to 11.3mm. This requires installation at a tire shop. Refe...

Acrylic Wind Blocker

Available options:Acrylic Wind Blocker with logo options - Fiat WBRC £100 Clear - no logo Size ...

£130.00(Inc VAT at 20%)
ACC Power Controller

This device will keep ACC power (accessory power) enabled until driver side door is opened or for 10 minutes after engine was...

£89.00(Inc VAT at 20%)
Red LED Strip with Rear Harness

High Power Red LED strip (480 LEDs/m) with 3M VHB backing tape. Strip comes with a 5' cable and connector to plug into the rear ...

£69.00(Inc VAT at 20%)
Rear Harness for LED Strip

This harness is designed to provide an easy access to the parking light wires for the additional LED strip or Wind Blocker illum...

£26.95(Inc VAT at 20%)
Air Bag Warning Overlay Replacement

Made from two-color, black on white 1.5mm acrylic with 3D printed frame. To install this plate, all you need to do is remove th...

£34.96(Inc VAT at 20%)
Rear Light Unit Harness

3" wire harness, for plug-n-play installation of ballast resistors for LED conversion; allows you to keep factory wires intact. O...

£36.00(Inc VAT at 20%)
Illumination kit for Acrylic Wind Blocker

This is the illumination kit for the acrylic wind blockers (4.5mm acrylic). LED enclosure 3D printed from black ABS.  Cab...

£50.00(Inc VAT at 20%)
Central Console Shelf

CENTRAL CONSOLE SHELF IS MADE FROM ALUMINUM, WITH A BLACK SILICONE COATING. Central Console Shelf will fit in the compartment bet...

£29.95(Inc VAT at 20%)
Turn Signal LED Light

Rear Turn Signal sequential LED lights with high power OSRAM LEDs. Manufactured in USA. Direct replacement of the WY21W bulb. Two...

£165.00(Inc VAT at 20%)
Cup Holder Phone Mount

3D printed assembly for phone holder with magnets or clip, base only, without phone holder. This base can be plugged into the e...

£50.00(Inc VAT at 20%)
Air Bag Warning Overlay Replacement - Fiat

Made from two color, black on white 1.5mm acrylic with 3D printed frame. To install this plate, all you need to do is remove or...

£34.96(Inc VAT at 20%)
Warning Timer for Turn Signal with Footwell Light

This is the add-on OBD-II device. It will produce warning sounds through an Instrument Cluster buzzer, if the turn signal is lef...

£79.00(Inc VAT at 20%)
DRL Harness
(1 review)

THIS HARNESS WILL ENABLE LED DRL WHEN HEADLIGHTS ARE ON. Note: this product is designed to work only with the LED DRL option ...

£49.00(Inc VAT at 20%)
Results : 1 - 18 of 18 |Show
Sort by :
Page of 1